Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revision Both sides next revision
ip_selctor [2014/12/30 18:15]
admin
ip_selctor [2014/12/30 22:08]
admin
Line 1: Line 1:
 ---- ----
 **IP Selctor** **IP Selctor**
 +with the MCP23008 and MCP23017
 ---- ----
  
- +**Preparing the RPi for I2C:**\\
-**MCP23008 and MCP23017**\\ +
-Configuration:\\+
 [[http://raspberrypi-aa.github.io/session3/i2c.html]]\\ [[http://raspberrypi-aa.github.io/session3/i2c.html]]\\
 [[http://www.gsurf.de/vorbereiten-des-raspberry-pi-auf-i2c/]]\\ [[http://www.gsurf.de/vorbereiten-des-raspberry-pi-auf-i2c/]]\\
 +Open the file:\\
 +  $ sudo nano /etc/modprobe.d/raspi-blacklist.conf
 +Comment out:\\
 +  #blacklist i2c-bcm2708
 +Open the file:\\
 +  $ sudo nano /etc/modules
 +Add:\\
 +  i2c-dev
 +Load modules:\\
 +  $ sudo modprobe i2c_bcm2708
 +  $ sudo modprobe i2c-dev
 +Check the i2c modules:\\
 +  $ lsmod
 +  
 +  Module                  Size  Used by
 +  i2c_dev                 3792 
 +  i2c_bcm2708             3408 
 +Install some programs:\\
 +  $ sudo apt-get update
 +  $ sudo apt-get install i2c-tools
 +  $ sudo apt-get install python-smbus
 +Check the address:\\
 +  $ sudo i2cdetect -y 1
 +  $ sudo i2cdump -y 1 0x20
  
-  sudo nano /etc/modprobe.d/raspi-blacklist.conf+**Library:**\\ 
 +[[https://learn.adafruit.com/mcp230xx-gpio-expander-on-the-raspberry-pi/overview]]\\ 
 +Download Adafruit libraries:\\ 
 +  $ wget https://github.com/adafruit/Adafruit-Raspberry-Pi-Python-Code/archive/master.zip 
 +unpack:\\ 
 +  $ unzip master.zip 
 +Example:\\ 
 +  # Set IP Address with MCP23008 
 +  from Adafruit_MCP230xx import * 
 +  # Use busnum = 0 for older Raspberry Pi's (256MB) 
 +  # Use busnum = 1 for new Raspberry Pi's (512MB with mounting holes) 
 +  mcp = Adafruit_MCP230XX(busnum = 1, address = 0x20, num_gpios = 8) 
 +  # Set pins to input with the pullup resistor enabled 
 +  for i in range(0,8): 
 +    mcp.pullup(i, 1) 
 +  # Read pins and display the results 
 +  #bitshift output, third bit is the output 
 +  meineIP=0 
 +  for i in range(0,8): 
 +    print "%d: %x" % (i, mcp.input(i) >> i) 
 +    meineIP = meineIP +  mcp.input(i) 
 +  print meineIP
  
  
-Library:\\ 
-[[https://learn.adafruit.com/mcp230xx-gpio-expander-on-the-raspberry-pi/overview]]\\